Diesel engines have been widely utilized as power sources for land transportation, ships, and construction machinery because of their high thermal efficiency. However, there is a disadvantage because harmful emissions such as nitrogen oxides (NO_x) and particulate matter (PM) are generated, owing to the high combustion temperature and chemical reaction of the inhomogeneous fuel-air mixture. To satisfy environmental regulations, the research on dual-fuel engines for ships continues, and efforts are made to optimize performance and efficiency, such as adjusting the common rail pressure. In addition, research to reduce the emission of harmful substances by the improvement and optimization of combustion methods, such as multi-stage injection, has been actively conducted [1]-[2].

To reduce NO_x emissions, it is important to lower the combustion temperature inside the combustion chamber. Accordingly, other fuels or substances can be mixed with the existing diesel fuel [3]. When methanol is utilized as a fuel additive, the oxygen content in the fuel increases, the heat of evaporation increases, and NO_x and PM during combustion tend to decrease [4]. Emulsified fuel, in which water is added to diesel fuel, reduces the internal temperature of the combustion chamber as water evaporates first during the combustion process [5]-[6]. In addition to these approaches, NO_x emissions can be reduced by using after-treatment technologies, such as selective catalyst reduction (SCR) or lean NO_x trap (LNT). Urea-SCR separates the NO_x contained in the exhaust gas into nitrogen and water, by utilizing NH₃ generated through thermal decomposition and hydrolysis of urea as a reducing agent. LNT absorbs NO_x under lean conditions and reduces NO_x to N₂ by supplying a reducing agent by an in-cylinder post-injection under rich conditions [7]-[9].

In addition, it is possible to improve engine performance and reduce the emission of various harmful substances by controlling the air-fuel ratio related to the formation of a mixture inside the combustion chamber, which can be done by regulating the air-throttle and exhaust gas recirculation (EGR) valves. Because the intake pressure of the air flowing into the combustion chamber affects the performance and concentration of exhaust gases, the turbocharger application is preferred over the naturally aspirated method, and the performance and efficiency of the engine can be improved by improving the efficiency of the turbocharger [10]-[15].

In this study, to investigate the effect of air throttling on the performance and emission characteristics of a naturally aspirated single-cylinder diesel engine, an experiment was conducted by gradually altering the load for three different levels of air throttling. Accordingly, the effect of air throttling on the performance and emission characteristics of MITSUKI's MIT-178F diesel engine was investigated under a wide range of operating conditions, and a database for future parametric studies was established.

Figure 1 is a schematic diagram of the MT502E PC-controlled single-cylinder engine testbed and exhaust gas measurement devices. The main specifications of the engine are presented in Table 1. The engine load and air throttling level can be controlled by a control box connected to a PC, thereby indirectly altering the air-fuel ratio. Significant physical quantities, including power and specific fuel consumption, and output are automatically calculated using a built-in software. The concentration of different species in the exhaust gas must be measured using a separate device. QROTECH's OPA-102 smoke meter was utilized to measure the concentration of PM, and QROTECH's QRO-402 gas analyzer was utilized to measure the concentration of significant emissions such as NO_x and CO.

Figure 1: 
Schematic diagram of the experimental apparatus

To investigate the performance and emission characteristics of a diesel engine by air throttling, 12 experimental conditions were tested, as presented in Table 2. The experiment was conducted at 1 atm and 18 °C, however, because it is an air-cooled type engine, a coolant was not utilized. The load was increased after setting the air throttling level by the PC connected to the control box for each experimental condition. At this time, as the load increased, the engine speed decreased, and the engine stopped when the specific load level was exceeded for a given air throttling level. Therefore, it is necessary to determine the operable load range according to the air throttling level by trial and error.

The manufacturer recommended testing at an air throttling level of 80% or lower; hence, pilot tests were conducted between 50% and 85%. However, at air throttling levels above 80%, the engine vibration was excessive. In addition, in conditions where the air throttling level was below 65%, the operating engine speed range was too narrow to establish various test conditions. Therefore, three air throttling levels of 65%, 70%, and 75% were chosen, and for each air throttling level, the engine speeds were set at an interval of 125 rpm. Adjusting the air throttling level altered the amount of air flowing into the combustion chamber; hence the air-fuel ratio for each condition was different.

After the engine reached a statistically steady state for each experimental condition, the data were sampled at intervals of 5 s for approximately 1 min, and the average was calculated. The maximum standard deviation was approximately 0.05 and 0.01 for torque and brake power, respectively, and the maximum standard deviation for CO, CO₂, and PM concentrations measured in percent was approximately 0.04. Regarding HC and NO_x concentrations measured in ppm, the maximum standard deviation was 3.3.

The MT502E testbed of the ESSOM facilitates the control of limited parameters, so there is a limit to performing parametric studies on other significant operating conditions. Therefore, the use of a numerical method for a detailed parametric study of a specific variable may be better.

The effects of air throttling on the performance and emission characteristics of the MITSUKI MIT-178F diesel engine were investigated under 12 experimental conditions, and the following results were obtained.

• (1) As the air throttling level increased, the torque generated by the engine increased , and for a given air throttling level, the torque generally decreased as the engine speed increased.
• (2) The fuel conversion efficiency was very low at air throttling levels of 65% and 70%, and there is a common tendency that the fuel conversion efficiency decreased as the engine speed increased at different air throttling levels.
• (3) At 65% air throttling, there is no clear correlation between the air-fuel ratio and the power; however, at 70% and 75% air throttling, the air-fuel ratio increased, while power appeared to decrease as the engine speed increased.
• (4) The higher the exhaust gas temperature, the higher the NO_x emissions, which means that the higher the proportion of thermal NO_x.

For different air throttling levels, the concentration of CO₂ decreased as the engine speed increased, and the concentration of PM appeared to decrease as the air-fuel ratio increased for air throttling levels of 70% and 75%.